kinetic.ENGINE LAB
AN INTERACTIVE MECHANICAL PLAYGROUND

Get to know what moves us.

Take it apart. Look a little closer. Put every piece back in motion.

ON THE WORKBENCHSingle-cylinder engine4-stroke · Air-cooled · SC–01 concept
LIVE 3D
Opening the engine lab…
SC–01 / ENGINE STUDYSingle-cylinder, four-stroke
100%
YZX
EDUCATIONAL MODEL15 INTERACTIVE ASSEMBLIES
0%
Hand tool
Drag to orbit Pinch / scroll to zoom Double-click to focus FREE ORBIT
A more hands-on experience.EXPERIMENTAL

Your webcam. Your hands. A whole new way to explore.

Your camera preview
CAMERA OFF
Open camera-only test
Your hands are the controller.
01Pinch & rotate

Choose Rotate / grab. Pinch over the engine and move. Pinch and release over a button to click.

02Zoom with your fingers

Choose Finger zoom and pinch over the engine. Spread thumb and index to zoom in; close to zoom out. Lower your hand to stop.

03Two-hand zoom

In any tool, pinch with both hands. Spread hands apart to zoom in, or bring them together to zoom out.

04Move the view

Choose Pan. Pinch and move your hand left, right, up, or down. Release to stop.

05Separate the parts

Choose Separate parts. Pinch and lift to spread the assemblies, or lower your hand to bring them together.

06Grab an assembly

Choose Rotate / grab in Assemble. Pinch a part, move your hand, then release to remove or install.

07Focus & reset

Point at Focus or Reset view and pinch to click. You can also pinch the + and − buttons for small zoom steps.

08Open palm to pause

Hold an open palm for one second. Hold again to resume. Losing the hand cancels a grab or finger zoom.

Camera frames are processed on this device. No audio is captured.Point at top / bottom screen edge to scroll
Built for curiosity.SC–01 is a simplified learning model, not a service or engineering simulator.
WELCOME TO YOUR WORKBENCH

A little curiosity.
A lot to discover.

Meet SC–01, a small, air-cooled, single-cylinder engine concept. Every visible component belongs to one of 15 interactive assemblies.

01 / Inspect

Drag to rotate freely, including underneath. Scroll or use +/− to zoom. Right-drag to pan. Double-click a part to focus, or select it in the component list. Use the camera menu for front, back, side, top and bottom views.

Exploded view separates assemblies. Cutaway slices the housing; X-ray makes it transparent. Isolate shows only the selected assembly.

02 / Assemble

Remove parts in a guided order. The inspector explains which connections need to come apart first. “Remove next” takes the next valid step; “Reassemble all” returns each part in reverse dependency order. You can pause this sequence at any point.

03 / Simulate

With all parts installed, explore the four-stroke cycle. Play or pause with Space, scrub through 720° of crankshaft rotation, or change the playback speed. Piston and rod positions follow a slider–crank relationship.

04 / Go hands-free

Enable your webcam and allow camera access. Point with your index finger, then pinch and release over a button to click. Pinch and move over the model to orbit in Inspect, or to remove/install a part in Assemble. Choose Finger zoom beneath the viewer: pinch over the engine, then spread your thumb and index finger to zoom in or bring them together to zoom out. Lower your hand to stop. You can also pinch with both hands and change the distance between them to zoom in any tool. Choose Pan to reposition the view, or Separate parts to spread the assemblies by pinching and lifting. Hold an open palm for a second to pause or resume controls.

Point near the top or bottom screen edge without pinching to scroll. Keep hands well lit and visible. Tracking is experimental; the mouse works at all times. Camera access requires localhost or HTTPS on another device. Frames stay on your device.

This is a procedural educational model. Fasteners are grouped, valve timing and the timing drive are simplified, and combustion, heat, loads and physical collisions are not calculated. Hand controls manipulate the model on your screen; they do not create a physical hologram.